"This was a fun activity for my Partner and I, there is better materials out there to use for this purpose however. I would recommend using a better thermometer than what is provided and make sure your water Temp is EXACTLY 90 degrees F. Definitely need a partner for this to help set up and keep you stimulated during the process. The molding powered ended up shrinking the mold in length as it dried and the silicone provided wasn’t enough for a larger man. Left us 2 inches short on the length and that was with using the provided vibrator to displace some of the space on the mold. The clone actually turned out pretty decent for what it was but unfortunately the material is very Hard and a little rough. It ended up not feeling good for my Wife and we were both kind of disappointed with that aspect of it. But it was still a fun experience for the cheap price point. With a little research after this experiment , one could easily find some more suitable/ softer material alternatives to actually make a usable, enjoyable clone for thier partner if that is what the desired outcome of getting a kit like this is for someone other than just novelty."

"Ok. So this requires a lot of preparation. I highly recommend 2 people.... possibly even a 3rd. We read all the reviews and watched lots of fail videos about it but still decided that we could conquer this. The first attempt was a complete and very messy fail. We had the water to the perfect temperature, ( Side note: I feel that some of the other reviewers may have been reading the included thermometer wrong. Make sure you are reading the fahrenheit side. ) the tube was cut and taped so as not to scratch him, we had everything set up so that we could go as fast as possible with timers set for every stage. So first of all from what I understand it is very hard to hold an erection while feeling under pressure from all these time sensitive steps. Finally with a little help from me and his favorite website he got to where he needed to be. I mixed the powder and water and stirred for 1 minute as described. It was very lumpy still when the timer went off but I went ahead and poured the mixture into the tube and proceeded to the next step which presented a logistical problem. The tube is full and he is standing... so I, being very aware of the time just tilted the tube and slapped it over his erection pushing it all the way to his body. In the process of this quite a bit of the molding material rained down onto the floor and all over his legs and feet. He tried really hard to maintain his concentration but the cold wet goo covering him did not help anything. We were still hopeful and waited the 4 minutes plus a little extra as a precaution. Removing the tube was not that fun for him either as he had not done any manscaping in preparation and it did stick a little bit. Once the tube was off we looked at what we had created. It was less than awe inspiring... There were clearly visible bubbles and not a very accurate impression had been made. While he cleaned up both himself and the floor in a 4 foot radius from where he had been standing I mixed the silicone material and poured it into the mold and then slid in and carefully positioned the included vibrator attached to a cardboard square as described. 24 hours later... We pulled the failure from the mold and were super disappointed that not only was it covered in lumps and pits but also the mold had warped a bit and it was shorter and thinner. Also the vibrator had touched the side of the mold and was visibly sticking out a little ways. No way would I ever be using that for anything. So... I am not easily deterred and came back on Amazon and ordered the Alginate powder that another reviewer suggested, a refill kit of the silicone material, some cock rings, and a natural performance enhancer. 3 nights later... I had him lay on the bed on top of towels. I cut both sides of the tube out so that it was open on both sides. He put on the cock ring and got himself to where he needed to be. I measured, poured and mixed everything ( by the way don't be afraid to use cold water with the alginate powder it will make it set slower ). I came back to him and placed the tube over him and poured the mixture into the tube and over his erection. Then kinda squeezed the tube a bit to make sure it covered everything. We waited 5 minutes and removed it. ( made significantly easier by him having done some manscaping ) and..... Perfect mold!!! No issues with mixing the silicone mixture. I do recommend that after you pour it into the mold you should come back about 1 hour later and pop all the bubbles that have formed at the top. 24 hours later and I now own a perfect replica of my mans "willy". It is awesome for those times when he isn't around. Also it was pretty fun even with the fails we were laughing quite a bit during the whole process."

"My biggest critique: The mold needs a LONGER time to solidify...... 2 minutes is not enough time (especially if you're doing it by yourself) If you rush, the mold looks like coliflower, if you're too slow, you just end up with an un-usable mold.

Tried suprising an FWB across the states by mailing her a mold of myself...... all I ended up with was a mess because you can't: Heat up, mix, time and keep yourself...... "motivated"....... for a proper mold. Definitely have someone mix it while you keep yourself "up" to the challenge"